|
|
 |
|
Empfehlungstabelle |
GIS
|
| Legierte
Stähle, Edelstähle |
PVC,
weich |
| Baustähle
geringerer Festigkeit |
|
|
PVC,
hart |
| Messing
hart, Buntmetalle allgemein |
|
|
Acrylglas |
| Kupfer,
Messing weich |
|
|
Polystyrol |
| Alucobond,
Dibond |
|
|
Kömacel,
Simona |
| Alu,
harte, kurzspanende Sorten |
|
|
Thermoplaste
allgemein |
| Alu,
plastisch (weich) |
|
|
Duroplaste
wie Bakelite, Pertinax |
| |
|
|
|
Graviermaterial,
Gravoply, Rowmark, ... |
| |
|
|
Verbundwerkstoffe |
| |
|
|
GFK,
CFK, Leiterplatten |
|
> Hinweise zum Gebrauch der
Tabelle... |
|
Weichholz
(Kiefer...) |
| |
|
|
Hartholz
(Buche, Ramin,...) |
|
= sehr gut geeignet |
|
|
Spanplatten,
Hartfaser, MDF |
= gut geeignet |
|
|
Leichtes
Sperrholz, Balsa |
= bedingt geeignet |
|
|
Pappe,
Cellulose, Filz |
| |
|
|
|
| Einschneider |
Besonderheit |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F112
/
F113 |
Up-
/ downcut |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F120 |
Alu-Spezialist |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F126 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Zweischneider |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F221 |
Stirnanschliff |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F240 |
Gerade
genutet |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F260 |
Stirnradius
180° |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F225 |
Downcut |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F246
/ F247 |
Universalfräser |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Verzahnte
Fräser |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F041 |
"diamant"-verzahnt |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F048 |
spiralverzahnt |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| | | | |
