 |
| Empfehlungstabelle
für Fräswerkzeuge aus
Hartmetall |
GIS |
| Legierte
Stähle, Edelstähle |
PVC,
weich |
| Baustähle
geringerer Festigkeit |
|
|
PVC,
hart |
| Messing
hart, Buntmetalle allgemein |
|
|
Acrylglas |
| Kupfer,
Messing weich |
|
|
Polystyrol |
| Alucobond,
Dibond |
|
|
Kömacel,
Simona |
| Alu,
harte, kurzspanende Sorten |
|
|
Thermoplaste
allgemein |
| Alu,
plastisch (weich) |
|
|
Duroplaste
wie Bakelite, Pertinax |
| |
|
|
|
Graviermaterial,
Gravoply, Rowmark, ... |
| |
|
|
Verbundwerkstoffe |
| |
|
|
GFK,
CFK, Leiterplatten |
|
>>> Hinweise zum Gebrauch der Tabelle... |
|
Weichholz
(Kiefer...) |
| |
|
|
Hartholz
(Buche, Ramin,...) |
|
= sehr gut geeignet |
|
|
Spanplatten,
Hartfaser, MDF |
= gut geeignet |
|
|
Leichtes
Sperrholz, Balsa |
= bedingt geeignet |
|
|
Pappe,
Cellulose, Filz |
| |
|
|
|
| Einschneider |
Besonderheit |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F112
/
F113 |
Up-
/ downcut |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F120 |
Alu-Spezialist |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F126 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Zweischneider |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F221 |
Stirnanschliff |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F240 |
Gerade
genutet |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F260 |
Stirnradius
180° |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F225 |
Downcut |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F246
/ F247 |
Universalfräser |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Verzahnte
Fräser |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F041 |
"diamant"-verzahnt |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| F048 |
spiralverzahnt |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Spezialfräser |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| FG02 |
Bohr-Fräser |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| FV16
/ FV17 |
Abschräger |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| CMT-Fräser |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| alle |
Holzfräser |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
GIS
Gienger Industrie-Service
• Segantinistr. 5 • CH
- 8049 Zürich • Tel. /
Fax +41-(0)44-341 5028 •
mail: info@gis-tec.com
Auslieferungslager EU •
Weimarstr. 15 • D -
78532 Tuttlingen • Tel.
+49-(0)7461-162020 • Fax
162021 |
|
